| Element Name | Element Description |
|---|
| <adapter> |
 Specifies a adapter. |
| <adaptertest> |
Specifies an adapter test. |
| <agent> |
Specifies a agent. |
| <agentmodel> |
Specifies an agent model. |
| <agentmodeltest> |
Specifies an agent model test. |
| <agenttest> |
Specifies an agent test. |
| <ascii> |
The ascii tag specifies the ASCII data
for a message or filter. Each character defines 8 bits
of data. |
| <baudrate> |
Specifies the serial port baud
rate. Common baud rates for a serial port:
- 110
- 300
- 1200
- 2400
- 4800
- 9600
- 19200
- 38400
- 57600
- 115200
- 230400
- 460800
- 921600
|
| <bigendian> |
Specifies that the parameter data
is in big endian order. This is the default order. |
| <boolean> |
Specifies a boolean value. |
| <bundle> |
Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created. |
| <byte> |
Specifies a byte of data. |
| <bytes> |
The bytes tag specifies the data for a
message or filter. Each byte defines 8 bits of data.
You can specify the numeric format base of the data with
the format attribute. |
| <character> |
Specifies a character value (16 bits). |
| <command> |
The command tag denotes an action that
can be performed by the hardware device. Usually, a
message must be sent to the hardware device to cause the
action to be performed. When an application requests a
command to be executed, the software device requests the
transport to send the command message to the hardware
device. For example, you might use the command tag to
send a message to a radio to "turn volume up"
or "turn on power". The commands that the
device should define are hardware specific. As such, the
command set for a radio differs from the command set for
a car bus. Also, the command set might vary based on the
company that built the device. To send effective
commands to hardware, be sure to use the hardware
specifications from the manufacturer.
Some commands can be executed with a parameter that will be
encoded into the message before it is sent to the hardware device.
The message that
represent the command are defined in a message tag. |
| <commandreceived> |
If content value is true, then the command received message can occur.
0 or 1 are valid. |
| <commandref> |
Specifies a command reference. |
| <commands> |
The commands tag enables you to couple
commands together. You can use the commands tag to
execute a series of commands in sequence. This tag can
have multiple command children. Use the idref attribute
to reference the actual commands under the commands tag.
The value of "idref" corresponds to the id of
a previously defined command. |
| <comport> |
Specifies the serial port com
port. This value starts at 1. |
| <concrete> |
The concrete tag defines the interface to
a software device. The command tags define the actions
that are supported by this software device. The signals
tags define the events that are supported by this
software device. The measurement tags define the
properties supported by this software device. Use the
transportservice tag to specify the
deviceā??s transport. You can specify
the Open Services Gateway Initiative (OSGi) service and
transport class implementation with the transportservice
tag. |
| <concretetest> |
Specifies a concrete test. |
| <configuration> |
If content value is true, then this is a configuration control.
0 or 1 are valid. |
| <connection> |
Specifies a connection to be used by the transport. |
| <connectionservice> |
Specifies a connection service to be used by the transport. |
| <connectiontest> |
Specifies an connection test. |
| <customparameter> |
Specifies a custom parameter. |
| <data> |
The data tag specifies a data
within a message. By using the data tag, the value
of the data can be extracted from the message
received from the hardware device. The data tag is
also used to define how to stored a data into a
message to be sent to the hardware device. This value in
the message can be translated into/from the application
value by using the translate tags. Valid subtags of
data include those that specify where to place the
data within the message and a series of transforms
that manipulate the data's data. You can set
the units of the data with the units tag. |
| <databits> |
Specifies the data bits for a serial port. |
| <deprecated> |
Specifies that parent Specifies that the contents of this element should be marked as deprecated.
|
| <description> |
Specifies the description of the parent
element. The description element documents the Device
Kit XML file and the generated code. |
| <device> |
The device tag is used to denote the
interface to a hardware device. The command tags denote
the actions that are supported by the hardware device.
The signals tags denote the events that are supported by
the hardware device. The measurement tags denote the
properties supported by the hardware device. Use the
transportservice tag to specify the
deviceā??s transport. You can specify
the Open Services Gateway Initiative (OSGi) service and
transport class implementation with the transportservice
tag. |
| <devicetest> |
Specifies a device test. |
| <dkml> |
Specifies the root element of a Device
Kit Markup Language (dkml) document. |
| <double> |
Specifies double data. |
| <echo> |
Specifies an echo connection. |
| <enum> |
Use the enum tag to specify a enum.
|
| <exportservice> |
Specifies the name of the Open Services
Gateway initiative (OSGi) service to be exported. |
| <field> |
Specifies the field parameter name. |
| <file> |
Specifies a file connection. |
| <filter> |
Use the filter tag to specify a filter
mask for a message. The bytes tag defines the relevant
filter bytes. All of the bits in the filter bytes that
are turned on will be compared and all bits that are
turned off will be ignored. |
| <float> |
Specifies float data. |
| <gpio> |
Specifies a General Purpose Input Output
(GPIO) connection. |
| <group> |
The group tag is used to denote the
interface to a hardware group. The command tags denote
the actions that are supported by the hardware group.
The signals tags denote the events that are supported by
the hardware group. The measurement tags denote the
properties supported by the hardware group. Use the
transportgroup tag to specify the
groupā??s transport. You can specify
the Open Services Gateway Initiative (OSGi) service and
transport class implementation with the transportservice
tag. |
| <hardwareflowcontrol> |
Specifies the serial port hardware
flow control value. |
| <host> |
Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) host name. |
| <i2c> |
Specifies an Inter-IC (i2c) connection. |
| <identifier> |
Specifies the parameter identifier. |
| <import> |
Specifies an import package. |
| <index> |
Specifies the starting
byte index of the
parameter within the message. Index 0 is the
first byte of the message. See the offset
element to specify the parameter offset in
bits. |
| <initializemeasurements> |
Specifies that the device should
initialize the measurements. |
| <inputname> |
Specifies the input file name. |
| <inputpath> |
Specifies the file input path name. |
| <insert> |
Specifies that the parameter
should be inserted into the message. |
| <int> |
Specifies integer data (32 bits). |
| <junit> |
Specifies junit test. Currently, not supported. |
| <key> |
Specifies a unique command key. |
| <length> |
Specifies the data
length in bits. See the
length
element to specify the data length in
bytes. |
| <linger> |
Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) linger
value. A value of -1 specifies to use the
default values. A value of zero speciifes no
linger. A value greater than zero is the
milliseconds linger value. See the Socket class
for more details. |
| <list> |
Specifies list data. |
| <littleendian> |
Specifies that the parameter data
is in little endian order. |
| <localhost> |
Specifies the multicast local host name. |
| <localport> |
Specifies the multicast local port. |
| <long> |
Specifies long data (64 bits). |
| <managedbundle> |
Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created. |
| <managedfactorybundle> |
Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created. |
| <map> |
Specifies map data. |
| <maximum> |
Specifies the maximum value. |
| <measurement> |
The measurement tag denotes a logical
property of the hardware device. This logical property
is usually stored in the hardware device and requires
that commands to be sent to the device to read
(readcommand tag) or write (writecommand tag) the value
of the measurement. The siganl tag is used to define the
signal that will be triggered when the value of the
measurement is sent by the hardware device. Hardware
devices vary on how the measurements are implemented.
Some hardware devices only support the reading of
measurement values and do not support writing new values
via messages. Other hardware devices support both
reading and writing of the measurement. Some hardware
devices support notification of the signal message when
the value changes while other hardware device require
that a read message be sent to get the measurement
value. See the hardware device specifications to
determain the correct tags that must be defined by this device. |
| <measurementref> |
Specifies a measurement reference. |
| <message> |
The message tag specifies the actual
message or set of bytes that the are sent or received
from the hardware device. The ascii, bytes, nibbles,
tokens, parameter, parameters, and filter subtags define
the content of a message. The specific tags to use
within the message tag depend on a combination of the
hardware specification and the controls that the
application needs. For example, if the hardware
communicates with bytes or eight bits use the bytes tag.
If the hardware understands four-bit increments (MOST),
use a series of nibbles to define the message. You can
also set a filter mask for a message. The contents of
the filter determine which bits are relevant. The
content of a binary message is often defined by using
the bytes subtag to specify a special byte or set of
bytes. The content of a American National Stardard Code
for Intormation Interchange (ASCII) message is normally
defined by using the ascii subtag. You can set the
delimiter with the tokens tag. Messages can also have
parameters that hold important value information.
Specify message parameters with the parameter and
parameters tags. Defining the messages correctly is very
important activity. WARNING: Defining the messages
incorrectly and sending the wrong messages to a hardware
device can be dangerous. |
| <messages> |
Specifies a group of messages. |
| <method> |
Specifies method data. |
| <minimum> |
Specifies the minimum value. |
| <mode> |
Specifies the file mode. |
| <monitor> |
Specifies monitor test. |
| <most> |
Specifies a Media Oriented Systems
Transport (MOST) connection. |
| <name> |
Specifies the file name. |
| <negative> |
Specifies the negative transform. |
| <nibbles> |
The nibbles tag specifies data for a
message. Each nibble defines 4 bits of data. You can
specify the numeric format base of data with the format
attribute. Normally, the hex format should be used to
define the data. |
| <noactivitytimeout> |
Specifies the timeout value in
milliseconds to wait for no activity. If no activity has
occurred after this time, the transport may attempt to
determine if the device is ok by sending a message to
the device. |
| <not> |
Specifies the not transform. |
| <offset> |
Specifies the starting
bit offset of the
parameter within the message. Offset 0 is
the first bit in the message. See the offset
element to specify the parameter offset in
bytes. |
| <outputname> |
Specifies the output file name. |
| <outputpath> |
Specifies the file output path name. |
| <packetsize> |
Specifies the multicast packet
size in bytes. |
| <parameter> |
The parameter tag specifies a parameter
within a message. By using the parameter tag, the value
of the parameter can be extracted from the message
received from the hardware device. The parameter tag is
also used to define how to stored a parameter into a
message to be sent to the hardware device. This value in
the message can be translated into/from the application
value by using the translate tags. Valid subtags of
parameter include those that specify where to place the
parameter within the message and a series of transforms
that manipulate the parameter's data. You can set
the units of the parameter with the units tag. |
| <parameters> |
Message can contain multiple parameters.
The parameters tag enables you to set multiple
parameters for a message. This tag can have mulitple
parameter children. The idref attribute references the
parameters in the parameters tag. The value of
"idref" corresponds to the id of a previously
defined parameter. |
| <parity> |
Specifies the parity of the serial port. |
| <path> |
Specifies the file path name. |
| <pid> |
The pid tag specifies a parameter
identifier (PID). By using the pid tag, the value of the
pid can be extracted from the message received from the
hardware device. The pid tag is also used to define how
to stored a parameter into a message to be sent to the
hardware device. This value in the message can be
translated into/from the application value by using the
translate tags. Valid subtags of parameter include
those that specify where to place the parameter within
the message and a series of transforms that manipulate
the parameter's data. You can set the units of the
parameter with the units tag. |
| <pids> |
The pids tag enables you to define the
set of pid supported. The idref attribute references
the pids in the pids tag. The value of "idref"
corresponds to the id of a previously defined pids. |
| <playback> |
Specifies playback test. |
| <port> |
Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) port. |
| <priority> |
Specifies the execution priority. |
| <productid> |
Specifies the USB product id. |
| <profile> |
The profile tag is used to denote the
interface to a hardware profile. The command tags denote
the actions that are supported by the hardware profile.
The signals tags denote the events that are supported by
the hardware profile. The measurement tags denote the
properties supported by the hardware profile. Use the
transportprofile tag to specify the
profileā??s transport. You can specify
the Open Services Gateway Initiative (OSGi) profile and
transport class implementation with the transportprofile
tag. |
| <profileparent> |
Specifies a profile reference. |
| <profileref> |
Specifies a profile reference. |
| <profiletest> |
Specifies an profile test. |
| <profileuses> |
Specifies a profile reference. |
| <provider> |
Specifies the provider name. Eclipse.org is an example of a provider. |
| <randomaccessfile> |
Specifies a random access file connection. |
| <rate> |
Specifies the polling rate in milliseconds. |
| <readcommand> |
The command tag denotes an action that
can be performed by the hardware device. Usually, a
message must be sent to the hardware device to cause the
action to be performed. When an application requests a
command to be executed, the software device requests the
transport to send the command message to the hardware
device. For example, you might use the command tag to
send a message to a radio to "turn volume up"
or "turn on power". The commands that the
device should define are hardware specific. As such, the
command set for a radio differs from the command set for
a car bus. Also, the command set might vary based on the
company that built the device. To send effective
commands to hardware, be sure to use the hardware
specifications from the manufacturer.
Some commands can be executed with a parameter that will be
encoded into the message before it is sent to the hardware device.
The message that
represent the command are defined in a message tag. |
| <readintervaltimeout> |
Specifies the number of
milliseconds that the serial port read between bytes. |
| <readtimeout> |
Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) read timeout
in milliseconds. |
| <readtotaltimeout> |
Specifies the maximum amount of
time in milliseconds that the serial port will
wait for a read. |
| <remotehost> |
Specifies the multicast remote
host name. |
| <remoteport> |
Specifies the multicast remote port. |
| <responsetimeout> |
Specifies the milliseconds to wait on a
response transport. |
| <retrytime> |
Specifies the milliseconds to wait before
attempting to retry the connection. |
| <scale> |
Specifies a scale transform. |
| <send> |
The send tag specifies the message(s) to
send. |
| <sentmessage> |
|
| <serial> |
Specifies a serial port connection. |
| <shift> |
Specifies a shitf transform. |
| <short> |
Specifies short data (16 bits). |
| <signal> |
The signal tag denotes a logical event
that can be triggered by the hardware device. Usually, a
signal defines a message that can be received from the
hardware device when an important event occurs. A
message tag defines the hardware-specific bytes that
represent the signal. See the hardware device
specifications more information about the specific bytes
that define the signal message. |
| <signalref> |
Specifies a signal reference. |
| <size> |
Specifies the data size
in bytes. See the length
element to specify the data length in
bits. |
| <sleep> |
Specifies a sleep command with the
content value in milliseconds. |
| <softwareflowcontrol> |
Specifies the serial port software
flow control value. |
| <spec> |
Specifies the hardware specification documentation. |
| <speccomment> |
Specifies a comment about the hardware
specification documentation. |
| <specdate> |
Specifies the date of the hardware
specification documentation. |
| <specreference> |
Specifies a reference to the hardware
specification documentation. |
| <specsection> |
Specifies the section in the hardware
specification documentation. |
| <spectitle> |
Specifies the title of the hardware
specification documentation. |
| <specvendor> |
Specifies the vendor of the hardware
specification documentation. |
| <specversion> |
Specifies the version of the hardware
specification documentation. |
| <stopbits> |
Specifies the stop bits of a serial port
connection. This value can be changed at runtime by
specifing the following in the property file:
lowercase transport
name.stopbits=value
<![CDATA[ gpsnmeatransport.stopbits=1 ]]> |
| <string> |
Specifies string data. |
| <tcpip> |
Specifies a Transmission Control
Protocol/Internet Protocol (TCP/IP) connection. |
| <tcpipserver> |
Specifies a Transmission Control
Protocol/Internet Protocol (TCP/IP) server connection. |
| <testagent> |
Specifies an test agent. |
| <testcase> |
Specifies a junit testcase test. |
| <testcount> |
Specifies the number of times to execute
the test cases. |
| <testdelay> |
Specifies the milliseconds time between
each test. |
| <testexecute> |
If content value is true, then the test
class will execute each command. 0 or 1 are valid. |
| <testexecuteread> |
If content value is true, then the
executeRead method should be invoked on all
measurements. 0 or 1 are valid. |
| <testexecutewrite> |
If content value is true, then the test
class will executeWrite each measuremnt. 0 or 1 are valid. |
| <testread> |
If content value is true, then the test
class will read each measuremnt. 0 or 1 are valid. |
| <testtrigger> |
If content value is true, then the test
class will trigger each signal. 0 or 1 are valid. |
| <tokens> |
Specifies the message tokens. |
| <translate> |
Specifies the translate (add) value. |
| <transport> |
Specifies a transport. |
| <transportservice> |
Specifies an Open Services Gateway
Initiative (OSGi) transport service name. |
| <transporttest> |
Specifies a transport test. |
| <udp> |
Specifies a User Diagram Protocol (UDP) transport. |
| <units> |
Specifies the units of a parameter or
measurement element. |
| <url> |
Specifies the Uniform Resource
Locator (URL) name. |
| <urlconnection> |
Specifies a Uniform Resource Locator
(URL) connection. |
| <usage> |
Specifies the USB usage. |
| <usagepage> |
Specifies the USB usage page. |
| <usb> |
Specifies a USB connection. |
| <value> |
Specifies a value. |
| <vendor> |
Specifies the vendor name. IBM is an example of a vendor. |
| <vendorid> |
Specifies the USB vendor id. |
| <version> |
Specifies the version level. The version
level should be one to three numbers seperated by a
period. For example, 1.0.0 is a valid version number. |
| <writecommand> |
The command tag denotes an action that
can be performed by the hardware device. Usually, a
message must be sent to the hardware device to cause the
action to be performed. When an application requests a
command to be executed, the software device requests the
transport to send the command message to the hardware
device. For example, you might use the command tag to
send a message to a radio to "turn volume up"
or "turn on power". The commands that the
device should define are hardware specific. As such, the
command set for a radio differs from the command set for
a car bus. Also, the command set might vary based on the
company that built the device. To send effective
commands to hardware, be sure to use the hardware
specifications from the manufacturer.
Some commands can be executed with a parameter that will be
encoded into the message before it is sent to the hardware device.
The message that
represent the command are defined in a message tag. |
| <writetotaltimeout> |
Specifies the serial port write
timeout value in milliseconds. |
| Element Name | Element Description |
|---|
| <dkml> | Specifies the root element of a Device Kit
Device Kit Language (dkml) document.
|
| ¦--<description> | Description of a Device Kit Markup
Language (dkml) element.
|
| ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.
|
| ¦--<provider> | Specifies the provider.
|
| ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.
|
| ¦--<vendor> | Specifies an implementing vendor.
|
| ¦--<pids> | Specifies the defined pids.
|
| ¦ ¦--<description> | Specifies the pids description.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<specreference> | Specification reference for pids.
|
| ¦ ¦ ¦--<description> | Description of the specification reference.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<spec> | The hardware specification documentation.
|
| ¦ ¦ ¦ ¦--<description> | Description of the specification.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<speccomment> | Comment about the hardware
specification documentation.
|
| ¦ ¦ ¦ ¦--<specdate> | Date of the hardware specification documentation.
|
| ¦ ¦ ¦ ¦--<spectitle> | Title of the hardware
specification documentation.
|
| ¦ ¦ ¦ ¦--<specvendor> | Vendor the hardware specification documentation.
|
| ¦ ¦ ¦ ¦--<specversion> | Version of the hardware
specification documentation.
|
| ¦ ¦ ¦--<specsection> | The reference to section in the
hardware specification documentation.
|
| ¦ ¦--<key> | Specifies the unique pids key.
|
| ¦ ¦--<pid> | Specifies the pid.
|
| ¦ ¦ ¦--<description> | Description of the parameter
identifier (PID).(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<specreference> | Specification reference for this
parameter identifier (PID).(see specreference) |
| ¦ ¦ ¦--<key> | Specifies the parameter identifier
(pid) key.(see key) |
| ¦ ¦ ¦--<identifier> | Specifies the parameter identifier.
|
| ¦ ¦ ¦--<length> | Specifies the parameter (pid)
data length in bits.
|
| ¦ ¦ ¦--<size> | Specifies the parameter
identifier (pid) size in
bytes. See the length
element to specify the parameter (pid) data
length in bits.
|
| ¦ ¦ ¦--<minimum> | Specifies the minimum value.
|
| ¦ ¦ ¦--<maximum> | Specifies the maximum value.
|
| ¦ ¦ ¦--<negative> | Negate the parameter value.
|
| ¦ ¦ ¦--<not> | Logical not of a boolean value.
|
| ¦ ¦ ¦--<scale> | Specifies the value to scale
the parameter value.
|
| ¦ ¦ ¦ ¦--<description> | Description of the scale.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this scale.(see specreference) |
| ¦ ¦ ¦--<shift> | Specifies the value to shift
the parameter value.
|
| ¦ ¦ ¦ ¦--<description> | Description of the shift.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this shift.(see specreference) |
| ¦ ¦ ¦--<translate> | Specifies the value to add
(translate) to the parameter value.
|
| ¦ ¦ ¦ ¦--<description> | Description of the translate.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this translate.(see specreference) |
| ¦ ¦ ¦--<units> | Specifies the optional parameter
identifier (pid) units.
|
| ¦ ¦ ¦ ¦--<description> | Description of the units.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this units.(see specreference) |
| ¦--<adapter> | Specifies an adapter.
|
| ¦ ¦--<description> | Description of the adapter.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this adapter.(see spec) |
| ¦ ¦--<specreference> | Specification reference for this adapter.(see specreference) |
| ¦ ¦--<customparameter> | Specifies a custom parameter for this adapter.
|
| ¦ ¦ ¦--<description> | Description of the custom parameter.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway Initiative (OSGi) adapter
service to be exported.
|
| ¦ ¦--<import> | Specifies the name of the
package to be imported.
|
| ¦ ¦--<profileref> | Specifies the name of the profile to be supported.
|
| ¦ ¦ ¦--<description> | Description of the profile reference.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<commandref> | Specifies a command reference.
|
| ¦ ¦ ¦ ¦--<description> | Description of the command reference.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<measurementref> | Specifies a measurement reference.
|
| ¦ ¦ ¦ ¦--<description> | Description of the measurement reference.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<signalref> | Specifies a signal reference.
|
| ¦ ¦ ¦ ¦--<description> | Description of the signal reference.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<command> | Defines a command supported by
this concrete device.
|
| ¦ ¦ ¦--<description> | Specifies the command description.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<specreference> | Specification reference for this command.(see specreference) |
| ¦ ¦ ¦--<key> | Specifies a unique command key.(see key) |
| ¦ ¦ ¦--<configuration> | Defines this command as a configuration command.
|
| ¦ ¦ ¦--<commandreceived> | Specifies if a command message can be received from the device.
|
| ¦ ¦ ¦--<rate> | Specifies the polling rate in milliseconds.
|
| ¦ ¦ ¦--<message> | Specifies the message to execute
the command.
|
| ¦ ¦ ¦ ¦--<description> | Description of the message.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this message.(see specreference) |
| ¦ ¦ ¦ ¦--<ascii> | Specifies a set of ASCII
character (8 bits).
|
| ¦ ¦ ¦ ¦--<bytes> | Specifies a set of bytes.
Each byte is 8 bits.
|
| ¦ ¦ ¦ ¦--<nibbles> | Specifies a set of nibbles.
Each nibble is 4 bits.
|
| ¦ ¦ ¦ ¦--<tokens> | Specifies the message tokens.
|
| ¦ ¦ ¦ ¦--<parameter> | Specifies a parameter within
the message.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the parameter.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this parameter.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<key> | Specifies the parameter key.(see key) |
| ¦ ¦ ¦ ¦ ¦--<bigendian> | Specifies that the parameter data
is in big endian order. This is the default order.
|
| ¦ ¦ ¦ ¦ ¦--<field> | Specifies the field parameter name.
|
| ¦ ¦ ¦ ¦ ¦--<insert> | Specifies that the parameter
should be inserted into the message.
|
| ¦ ¦ ¦ ¦ ¦--<littleendian> | Specifies that the parameter data
is in little endian order.
|
| ¦ ¦ ¦ ¦ ¦--<offset> | Specifies the starting
bit offset of the
parameter within the message. Offset 0 is
the first bit in the message. See the offset
element to specify the parameter offset in
bytes.
|
| ¦ ¦ ¦ ¦ ¦--<index> | Specifies the starting
byte index of the
parameter within the message. Index 0 is the
first byte of the message. See the offset
element to specify the parameter offset in
bits.
|
| ¦ ¦ ¦ ¦ ¦--<length> | Specifies the parameter
length in bits. See the
length
element to specify the parameter length in
bytes. (see length) |
| ¦ ¦ ¦ ¦ ¦--<size> | Specifies the parameter size
in bytes. See the length
element to specify the parameter length in
bits. (see size) |
| ¦ ¦ ¦ ¦ ¦--<enum> | Specifies a enum for this parameter.
|
| ¦ ¦ ¦ ¦ ¦ ¦--<description> | Description of the enum.(see description) |
| ¦ ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this enum.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<minimum> | Specifies the minimum value.(see minimum) |
| ¦ ¦ ¦ ¦ ¦--<maximum> | Specifies the maximum value.(see maximum) |
| ¦ ¦ ¦ ¦ ¦--<negative> | Negate the parameter value.(see negative) |
| ¦ ¦ ¦ ¦ ¦--<not> | Logical not of a boolean value.(see not) |
| ¦ ¦ ¦ ¦ ¦--<scale> | Specifies the value to scale
the parameter value.(see scale) |
| ¦ ¦ ¦ ¦ ¦--<shift> | Specifies the value to shift
the parameter value.(see shift) |
| ¦ ¦ ¦ ¦ ¦--<translate> | Specifies the value to add
(translate) to the parameter value.(see translate) |
| ¦ ¦ ¦ ¦ ¦--<units> | Specifies the optional parameter units.(see units) |
| ¦ ¦ ¦ ¦--<parameters> | Specifies a group of parameters.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Specifies the parameters description.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
group of parameters.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<key> | Specifies the unique parameters key.(see key) |
| ¦ ¦ ¦ ¦ ¦--<parameter> | Specifies the parameter.(see parameter) |
| ¦ ¦ ¦ ¦--<filter> | Specifies the message filter.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the filter.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this filter.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<bytes> | Specifies the message filter (Bit
off - ignore, Bit on - compare).(see bytes) |
| ¦ ¦ ¦ ¦--<sentmessage> | Specifies the message that was
sent that caused this message.
|
| ¦ ¦ ¦--<method> | Specifies the method to execute
the command.
|
| ¦ ¦ ¦--<data> | Specifies the data to execute
the command.
|
| ¦ ¦ ¦ ¦--<description> | Description of the data.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this data.(see specreference) |
| ¦ ¦ ¦ ¦--<key> | Specifies the data key.(see key) |
| ¦ ¦ ¦ ¦--<length> | Specifies the data
length in bits. See the
length
element to specify the data length in
bytes. (see length) |
| ¦ ¦ ¦ ¦--<size> | Specifies the data size
in bytes. See the length
element to specify the data length in
bits. (see size) |
| ¦ ¦ ¦ ¦--<minimum> | Specifies the minimum value.(see minimum) |
| ¦ ¦ ¦ ¦--<maximum> | Specifies the maximum value.(see maximum) |
| ¦ ¦ ¦ ¦--<units> | Specifies the optional data units.(see units) |
| ¦ ¦ ¦--<measurement> | Specifies the measurement to get the value for the command.
|
| ¦ ¦--<commands> | Specifies a command group.
|
| ¦ ¦ ¦--<description> | Specifies the commands description.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<specreference> | Specification reference for this
group of commands.(see specreference) |
| ¦ ¦ ¦--<key> | Specifies a unique commands key.(see key) |
| ¦ ¦ ¦--<configuration> | Defines this command as a configuration command.
(see configuration) |
| ¦ ¦ ¦--<commandreceived> | Specifies if a command message can be received from the device.
(see commandreceived) |
| ¦ ¦ ¦--<command> | Specifies the command within
the group of commands.(see command) |
| ¦ ¦ ¦--<sleep> | Specifies a sleep command.
|
| ¦ ¦--<group> | Defines a group
supported by this concrete device.
|
| ¦ ¦ ¦--<description> | Description of the group.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<spec> | Hardware specification
documentation for this group.(see spec) |
| ¦ ¦ ¦--<specreference> | Specification reference for this group.(see specreference) |
| ¦ ¦ ¦--<commandreceived> | Specifies if a command message can be received from the group.
(see commandreceived) |
| ¦ ¦ ¦--<key> | Specifies an optional key value.(see key) |
| ¦ ¦ ¦--<command> | Specifies a command that is
supported by this group.(see command) |
| ¦ ¦ ¦--<commands> | Specifies a command group.(see commands) |
| ¦ ¦ ¦--<measurement> | Specifies a measurement
supported by this group.(see measurement) |
| ¦ ¦ ¦--<signal> | Specifies a signal supported
by this group.
|
| ¦ ¦ ¦ ¦--<description> | Specifies the signal description.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this signal.(see specreference) |
| ¦ ¦ ¦ ¦--<key> | Specifies the unique signal key.(see key) |
| ¦ ¦ ¦ ¦--<configuration> | Defines this signal as a configuration signal.
(see configuration) |
| ¦ ¦ ¦ ¦--<rate> | Specifies the rate that the signal
is received in milliseconds.(see rate) |
| ¦ ¦ ¦ ¦--<message> | Specifies the message to
trigger the signal.(see message) |
| ¦ ¦ ¦ ¦--<method> | Specifies the method to handle
the signal.(see method) |
| ¦ ¦ ¦ ¦--<data> | Specifies the data when
the signal triggers.(see data) |
| ¦ ¦ ¦ ¦--<messages> | Specifies the messages to
trigger the signal.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Specifies the messages description.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
group of messages.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<key> | Specifies the unique messages key.(see key) |
| ¦ ¦ ¦ ¦ ¦--<message> | Specifies the message.(see message) |
| ¦ ¦ ¦ ¦--<pid> | Specifies the pid for this signal.(see pid) |
| ¦ ¦ ¦ ¦--<parameter> | Specifies a message parameter.(see parameter) |
| ¦ ¦ ¦ ¦--<parameters> | Specifies a parameter group.(see parameters) |
| ¦ ¦ ¦ ¦--<maximum> | Specifies the maximum value.(see maximum) |
| ¦ ¦ ¦ ¦--<minimum> | Specifies the minimum value.(see minimum) |
| ¦ ¦ ¦ ¦--<negative> | Negate the value.(see negative) |
| ¦ ¦ ¦ ¦--<not> | Logical not of a boolean value.(see not) |
| ¦ ¦ ¦ ¦--<scale> | Scale the value.(see scale) |
| ¦ ¦ ¦ ¦--<shift> | Shift the value.(see shift) |
| ¦ ¦ ¦ ¦--<translate> | Translate (add) to the value.(see translate) |
| ¦ ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway initiative (OSGi) group
to be exported.(see exportservice) |
| ¦ ¦ ¦--<import> | Specifies the name of the
package of be imported.(see import) |
| ¦ ¦--<measurement> | Defines a measurement
supported by this concrete device.(see measurement) |
| ¦ ¦--<signal> | Defines a signal supported by
this concrete device.(see signal) |
| ¦ ¦--<device> | Specifies the device used
by the adapter.
|
| ¦ ¦ ¦--<description> | Description of the device.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦ ¦--<spec> | Hardware specification
documentation for this device.(see spec) |
| ¦ ¦ ¦--<specreference> | Specification reference for this device.(see specreference) |
| ¦ ¦ ¦--<commandreceived> | Specifies if a command message can be received from the device.
(see commandreceived) |
| ¦ ¦ ¦--<initializemeasurements> | Specifies that the device should
initialize the measurements when the device is started.
|
| ¦ ¦ ¦--<key> | Specifies an optional key value.(see key) |
| ¦ ¦ ¦--<pids> | Specifies the defined pids.(see pids) |
| ¦ ¦ ¦--<priority> | Specifies the device execution priority.
|
| ¦ ¦ ¦--<command> | Specifies a command that is
supported by this device.(see command) |
| ¦ ¦ ¦--<commands> | Specifies a command group.(see commands) |
| ¦ ¦ ¦--<group> | Defines a group
supported by this device.(see group) |
| ¦ ¦ ¦--<measurement> | Specifies a measurement
supported by this device.(see measurement) |
| ¦ ¦ ¦--<signal> | Specifies a signal supported
by this device.(see signal) |
| ¦ ¦ ¦--<commandref> | Specifies a command reference.(see commandref) |
| ¦ ¦ ¦--<measurementref> | Specifies a measurement reference.(see measurementref) |
| ¦ ¦ ¦--<signalref> | Specifies a signal reference.(see signalref) |
| ¦ ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway initiative (OSGi) service
to be exported.(see exportservice) |
| ¦ ¦ ¦--<import> | Specifies the name of the
package of be imported.(see import) |
| ¦ ¦ ¦--<transport> | Specifies the transport used
by the device.
|
| ¦ ¦ ¦ ¦--<description> | Description of the transport.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦ ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦ ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦ ¦ ¦--<spec> | Hardware specification
documentation for this device.(see spec) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this transport.(see specreference) |
| ¦ ¦ ¦ ¦--<customparameter> | Specifies a custom parameter.(see customparameter) |
| ¦ ¦ ¦ ¦--<noactivitytimeout> | No activity timeout value in milliseconds.
|
| ¦ ¦ ¦ ¦--<responsetimeout> | Response timeoutout value in milliseconds.
|
| ¦ ¦ ¦ ¦--<retrytime> | Retry time value in milliseconds.
|
| ¦ ¦ ¦ ¦--<message> | Specifies a transport message.(see message) |
| ¦ ¦ ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway Initiative (OSGi) transport
service to be exported.(see exportservice) |
| ¦ ¦ ¦ ¦--<import> | Specifies the name of the
package to be imported.(see import) |
| ¦ ¦ ¦ ¦--<connectionservice> | Specifies the connection used
by the transport.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the connection service.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this connection service.(see specreference) |
| ¦ ¦ ¦ ¦--<echo> | Specifies an echo connection.
|
| ¦ ¦ ¦ ¦--<file> | Specifies a file connection.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the file connection.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
file connection.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<inputpath> | Specifies the file input path name.
|
| ¦ ¦ ¦ ¦ ¦--<inputname> | Specifies the input file name.
|
| ¦ ¦ ¦ ¦ ¦--<outputpath> | Specifies the file output path name.
|
| ¦ ¦ ¦ ¦ ¦--<outputname> | Specifies the output file name.
|
| ¦ ¦ ¦ ¦--<gpio> | Specifies a General Purpose
Input Output (GPIO) connection.
|
| ¦ ¦ ¦ ¦--<i2c> | Specifies an Inter-IC (I2C) connection.
|
| ¦ ¦ ¦ ¦--<most> | Specifies a Media Oriented
Systems Transport (MOST) connection.
|
| ¦ ¦ ¦ ¦--<randomaccessfile> | Specifies a random access file connection.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the random access
file connection.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
random access file connection.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<name> | Specifies the file name.
|
| ¦ ¦ ¦ ¦ ¦--<mode> | Specifies the file mode.
|
| ¦ ¦ ¦ ¦ ¦--<path> | Specifies the file path name.
|
| ¦ ¦ ¦ ¦--<serial> | Specifies a serial port connection.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the serial connection.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
serial connection.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<baudrate> | Specifies the serial port baud
rate. Common baud rates for a serial port:
- 110
- 300
- 1200
- 2400
- 4800
- 9600
- 19200
- 38400
- 57600
- 115200
- 230400
- 460800
- 921600
|
| ¦ ¦ ¦ ¦ ¦--<comport> | Specifies the serial port com
port. This value starts at 1.
|
| ¦ ¦ ¦ ¦ ¦--<databits> | Specifies the serial port data bits.
|
| ¦ ¦ ¦ ¦ ¦--<hardwareflowcontrol> | Specifies the serial port hardware
flow control value.
|
| ¦ ¦ ¦ ¦ ¦--<parity> | Specifies the serial port parity.
|
| ¦ ¦ ¦ ¦ ¦--<readintervaltimeout> | Specifies the number of
milliseconds that the serial port read between bytes.
|
| ¦ ¦ ¦ ¦ ¦--<readtotaltimeout> | Specifies the maximum amount of
time in milliseconds that the serial port will
wait for a read.
|
| ¦ ¦ ¦ ¦ ¦--<softwareflowcontrol> | Specifies the serial port software
flow control value.
|
| ¦ ¦ ¦ ¦ ¦--<stopbits> | Specifies the serial port stop bits.
|
| ¦ ¦ ¦ ¦ ¦--<writetotaltimeout> | Specifies the serial port write
timeout value in milliseconds.
|
| ¦ ¦ ¦ ¦--<tcpip> | Specifies a Transmission
Control Protocol/Internet Protocol (TCP/IP) connection.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the Transmission
Control Protocol/Internet Protocol (TCP/IP) connection.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
Transmission Control Protocol/Internet Protocol
(TCP/IP) connection.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<host> | Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) host name.
|
| ¦ ¦ ¦ ¦ ¦--<remoteport> | Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) remote port.
|
| ¦ ¦ ¦ ¦ ¦--<localport> | Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) local port.
|
| ¦ ¦ ¦ ¦ ¦--<linger> | Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) linger
value. A value of -1 specifies to use the
default values. A value of zero speciifes no
linger. A value greater than zero is the
milliseconds linger value. See the Socket class
for more details.
|
| ¦ ¦ ¦ ¦ ¦--<readtimeout> | Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) read timeout
in milliseconds.
|
| ¦ ¦ ¦ ¦--<tcpipserver> | Specifies a Transmission
Control Protocol/Internet Protocol (TCP/IP)
server connection.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the Transmission
Control Protocol/Internet Protocol (TCP/IP)
server connection.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
Transmission Control Protocol/Internet Protocol
(TCP/IP) server connection.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<port> | Specifies the Transmission Control
Protocol/Internet Protocol (TCP/IP) port.
|
| ¦ ¦ ¦ ¦--<urlconnection> | Specifies a Uniform Resource
Locator (URL) connection.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the Uniform
Resource Locator (URL) connection.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
Uniform Resource Locator (URL) connection.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<url> | Specifies the Uniform Resource
Locator (URL) name.
|
| ¦ ¦ ¦ ¦--<usb> | Specifies a USB connection.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the USB connection.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
USB connection.(see specreference) |
| ¦ ¦ ¦ ¦ ¦--<productid> | Specifies the USB product id.
|
| ¦ ¦ ¦ ¦ ¦--<usage> | Specifies the USB usage.
|
| ¦ ¦ ¦ ¦ ¦--<usagepage> | Specifies the USB usage page.
|
| ¦ ¦ ¦ ¦ ¦--<vendorid> | Specifies the USB vendor id.
|
| ¦ ¦ ¦ ¦--<transportservice> | Specifies the name of the Open
Services Gateway Initiative (OSGi) transport
service to be used by the transport.
|
| ¦ ¦ ¦ ¦ ¦--<description> | Description of the Open Services
Gateway Initiative (OSGi) transport service.(see description) |
| ¦ ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.
|
| ¦ ¦ ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.
|
| ¦ ¦ ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.
|
| ¦ ¦ ¦--<transportservice> | Specifies the Open Services
Gateway Initiative (OSGi) transport service name.(see transportservice) |
| ¦ ¦ ¦--<udp> | Specifies a User Diagram
Protocol (UDP) transport.
|
| ¦ ¦ ¦ ¦--<description> | Description of the User Diagram
Protocol (UDP) transport.(see description) |
| ¦ ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦ ¦--<specreference> | Specification reference for this
User Diagram Protocol (UDP) transport.(see specreference) |
| ¦ ¦ ¦ ¦--<remotehost> | Specifies the User Datagram
Protocol (UDP) remote host name.
|
| ¦ ¦ ¦ ¦--<remoteport> | Specifies the User Datagram
Protocol (UDP) remote port.(see remoteport) |
| ¦ ¦ ¦ ¦--<localhost> | Specifies the User Datagram
Protocol (UDP) local host name.
|
| ¦ ¦ ¦ ¦--<localport> | Specifies the User Datagram
Protocol (UDP) local port.(see localport) |
| ¦ ¦ ¦ ¦--<packetsize> | Specifies the User Datagram
Protocol (UDP) packet size in bytes.
|
| ¦ ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<adaptertest> | Specifies an adapter test.
|
| ¦ ¦--<description> | Description of the adapter test.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this adapter.(see spec) |
| ¦ ¦--<send> | Specifies the message(s) to send
during the test.
|
| ¦ ¦ ¦--<description> | Specifies the send description.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<specreference> | Specification reference for this send.(see specreference) |
| ¦ ¦ ¦--<message> | Specifies the message to send.(see message) |
| ¦ ¦ ¦--<sleep> | Specifies a sleep time.(see sleep) |
| ¦ ¦--<adapter> | Specifies the adapter to be tested.(see adapter) |
| ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.
|
| ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.
|
| ¦ ¦--<junit> | Specifies a junit test. Currently, not supported.
|
| ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported.
|
| ¦ ¦ ¦--<description> | Description of the monitor test.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<playback> | Specifies a playback test. Currently, not supported.
|
| ¦ ¦ ¦--<description> | Description of the playback test.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<testcase> | Specifies a junit testcase.
|
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<agent> | Specifies an agent.
|
| ¦ ¦--<description> | Description of the agent.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this agent.(see spec) |
| ¦ ¦--<specreference> | Specification reference for this agent.(see specreference) |
| ¦ ¦--<customparameter> | Specifies a custom parameter for this agent.(see customparameter) |
| ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway Initiative (OSGi) agent
service to be exported.(see exportservice) |
| ¦ ¦--<import> | Specifies the name of the
package to be imported.(see import) |
| ¦ ¦--<agentmodel> | Specifies the agent model used
by the agent.
|
| ¦ ¦ ¦--<description> | Description of the agent model.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦ ¦--<spec> | Hardware specification
documentation for this device.(see spec) |
| ¦ ¦ ¦--<specreference> | Specification reference for this agent model.(see specreference) |
| ¦ ¦ ¦--<customparameter> | Specifies a custom parameter for this agent model.(see customparameter) |
| ¦ ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway Initiative (OSGi) agent
service to be exported.(see exportservice) |
| ¦ ¦ ¦--<import> | Specifies the name of the
package to be imported.(see import) |
| ¦ ¦ ¦--<device> | Specifies the device used
by the agent model.(see device) |
| ¦ ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦ ¦--<device> | Specifies the device used
by the agent.(see device) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<agentmodel> | Specifies the agent model used
by the agent.(see agentmodel) |
| ¦--<agenttest> | Specifies an agent test.
|
| ¦ ¦--<description> | Description of the agent test.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this agent.(see spec) |
| ¦ ¦--<send> | Specifies the message(s) to send
during the test.(see send) |
| ¦ ¦--<agent> | Specifies the agent to be tested.(see agent) |
| ¦ ¦--<agentmodeltest> | Specifies the agent model test.
|
| ¦ ¦ ¦--<description> | Description of the agent model test.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦ ¦--<spec> | Hardware specification
documentation for this device.(see spec) |
| ¦ ¦ ¦--<agentmodel> | Specifies the agent model to be tested.(see agentmodel) |
| ¦ ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.(see testcount) |
| ¦ ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.(see testdelay) |
| ¦ ¦ ¦--<junit> | Specifies a junit test. Currently, not supported.(see junit) |
| ¦ ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported.(see monitor) |
| ¦ ¦ ¦--<playback> | Specifies a playback test. Currently, not supported.(see playback) |
| ¦ ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.(see testcount) |
| ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.(see testdelay) |
| ¦ ¦--<junit> | Specifies a junit test. Currently, not supported.(see junit) |
| ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported.(see monitor) |
| ¦ ¦--<playback> | Specifies a playback test. Currently, not supported.(see playback) |
| ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦--<agentmodeltest> | Specifies an agent model test.(see agentmodeltest) |
| ¦--<concrete> | Specifies a concrete device.
|
| ¦ ¦--<description> | Description of the concrete device.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this concrete device.(see spec) |
| ¦ ¦--<specreference> | Specification reference for this
concrete device.(see specreference) |
| ¦ ¦--<commandreceived> | Specifies if a command message can be received from the device.
(see commandreceived) |
| ¦ ¦--<initializemeasurements> | Specifies that the device should
initialize the measurements.(see initializemeasurements) |
| ¦ ¦--<key> | Specifies an optional key value.(see key) |
| ¦ ¦--<pids> | Specifies the defined pids.(see pids) |
| ¦ ¦--<command> | Defines a command supported by
this concrete device.(see command) |
| ¦ ¦--<commands> | Specifies a command group.(see commands) |
| ¦ ¦--<group> | Defines a group
supported by this concrete device.(see group) |
| ¦ ¦--<measurement> | Defines a measurement
supported by this concrete device.(see measurement) |
| ¦ ¦--<signal> | Defines a signal supported by
this concrete device.(see signal) |
| ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway initiative (OSGi) service
to be exported.(see exportservice) |
| ¦ ¦--<import> | Specifies the name of a
package to be imported.(see import) |
| ¦ ¦--<transport> | Specifies the transport used
by the device.(see transport) |
| ¦ ¦--<transportservice> | Specifies the name of the Open
Services Gateway Initiative (OSGi) transport
service to be used by the device.(see transportservice) |
| ¦ ¦--<udp> | Specifies a User Diagram
Protocol (UDP) transport.(see udp) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<concretetest> | Specifies a concrete test.
|
| ¦ ¦--<description> | Description of the concrete test.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this concrete device.(see spec) |
| ¦ ¦--<concrete> | Specifies the concrete device to
be tested.(see concrete) |
| ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.(see testcount) |
| ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.(see testdelay) |
| ¦ ¦--<testexecute> | Specifies if all commands should
be executed.
|
| ¦ ¦--<testexecuteread> | Specifies if the executeRead
method should be invoked on all measurements.
|
| ¦ ¦--<testexecutewrite> | Specifies if the executeWrite
method should be invoked on all measurements.
|
| ¦ ¦--<testread> | Specifies if the read method
should be invoked on all measurements.
|
| ¦ ¦--<testtrigger> | Specifies if all signals should be triggered.
|
| ¦ ¦--<junit> | Specifies a junit test. Currently, not supported(see junit) |
| ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported(see monitor) |
| ¦ ¦--<playback> | Specifies a playback test. Currently, not supported(see playback) |
| ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦--<connection> | Specifies an connection.
|
| ¦ ¦--<description> | Description of the connection.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<specreference> | Specification reference for this connection.(see specreference) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<connectiontest> | Specifies an connection test.
|
| ¦ ¦--<description> | Description of the connection test.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this connection.(see spec) |
| ¦ ¦--<send> | Specifies the message(s) to send
during the test.(see send) |
| ¦ ¦--<connection> | Specifies the connection to be tested.(see connection) |
| ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.(see testcount) |
| ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.(see testdelay) |
| ¦ ¦--<junit> | Specifies a junit test. Currently, not supported.(see junit) |
| ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported.(see monitor) |
| ¦ ¦--<playback> | Specifies a playback test. Currently, not supported.(see playback) |
| ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦--<device> | Specifies a device.(see device) |
| ¦--<devicetest> | Specifies a device test.
|
| ¦ ¦--<description> | Description of the device test.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this device test.(see spec) |
| ¦ ¦--<device> | Specifies the device to be tested.(see device) |
| ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.(see testcount) |
| ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.(see testdelay) |
| ¦ ¦--<testexecute> | Specifies if all commands should
be executed.(see testexecute) |
| ¦ ¦--<testexecuteread> | Specifies if the executeRead
method should be invoked on all measurements.(see testexecuteread) |
| ¦ ¦--<testexecutewrite> | Specifies if the executeWrite
method should be invoked on all measurements.(see testexecutewrite) |
| ¦ ¦--<testread> | Specifies if the read method
should be invoked on all measurements.(see testread) |
| ¦ ¦--<testtrigger> | Specifies if all signals should be triggered.(see testtrigger) |
| ¦ ¦--<junit> | Specifies a junit test. Currently, not supported.(see junit) |
| ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported.(see monitor) |
| ¦ ¦--<playback> | Specifies a playback test. Currently, not supported.(see playback) |
| ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<profile> | Specifies a profile.
|
| ¦ ¦--<description> | Description of the profile.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this profile.(see spec) |
| ¦ ¦--<specreference> | Specification reference for this profile.(see specreference) |
| ¦ ¦--<customparameter> | Specifies a custom parameter for this adapter.(see customparameter) |
| ¦ ¦--<profileparent> | Profile parent.
|
| ¦ ¦ ¦--<description> | Description of the profile reference.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<profileref> | Specifies profile parent.(see profileref) |
| ¦ ¦--<profileuses> | Profile uses.
|
| ¦ ¦ ¦--<description> | Description of the profile reference.(see description) |
| ¦ ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦ ¦--<profileref> | Specifies profile uses.(see profileref) |
| ¦ ¦--<commandreceived> | Specifies if a command message can be received from the profile.
(see commandreceived) |
| ¦ ¦--<key> | Specifies an optional key value.(see key) |
| ¦ ¦--<command> | Specifies a command that is
supported by this profile.(see command) |
| ¦ ¦--<commands> | Specifies a command group.(see commands) |
| ¦ ¦--<group> | Defines a group
supported by this profile.(see group) |
| ¦ ¦--<measurement> | Specifies a measurement
supported by this profile.(see measurement) |
| ¦ ¦--<signal> | Specifies a signal supported
by this profile.(see signal) |
| ¦ ¦--<exportservice> | Specifies the name of the Open
Services Gateway initiative (OSGi) service
to be exported.(see exportservice) |
| ¦ ¦--<import> | Specifies the name of the
package of be imported.(see import) |
| ¦ ¦--<adapter> | Specifies the adapter used
by the profile.(see adapter) |
| ¦ ¦--<device> | Specifies the device used
by the profile.(see device) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<profiletest> | Specifies a profile test.
|
| ¦ ¦--<description> | Description of the profile test.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this profile.(see spec) |
| ¦ ¦--<send> | Specifies the message(s) to send
during the test.(see send) |
| ¦ ¦--<profile> | Specifies the profile to be tested.(see profile) |
| ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.(see testcount) |
| ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.(see testdelay) |
| ¦ ¦--<junit> | Specifies a junit test. Currently, not supported.(see junit) |
| ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported.(see monitor) |
| ¦ ¦--<playback> | Specifies a playback test. Currently, not supported.(see playback) |
| ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<testagent> | Specifies a test agent.
|
| ¦ ¦--<description> | Description of the test agent.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this test.(see spec) |
| ¦ ¦--<profile> | Specifies the profile to be tested.(see profile) |
| ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
| ¦--<transport> | Specifies a transport.(see transport) |
| ¦--<transporttest> | Specifies a transport test.
|
| ¦ ¦--<description> | Description of transport test.(see description) |
| ¦ ¦--<deprecated> | Specifies that the contents of this element should be marked as deprecated.(see deprecated) |
| ¦ ¦--<provider> | Specifies the provider.(see provider) |
| ¦ ¦--<version> | Specifies the version level. The
format of the version number should be n.n.n
where n is a number. For example, 1.0.0 is a
valid version.(see version) |
| ¦ ¦--<vendor> | Specifies an implementing vendor.(see vendor) |
| ¦ ¦--<spec> | Hardware specification
documentation for this device.(see spec) |
| ¦ ¦--<send> | Specifies the message(s) to send
during the test.(see send) |
| ¦ ¦--<transport> | Specifies the transport to be tested.(see transport) |
| ¦ ¦--<testcount> | Unsigned integer that specifies
the number of times to execute tests.(see testcount) |
| ¦ ¦--<testdelay> | Specifies the milliseconds to
sleep between each test.(see testdelay) |
| ¦ ¦--<junit> | Specifies a junit test. Currently, not supported.(see junit) |
| ¦ ¦--<monitor> | Specifies a monitor test. Currently, not supported.(see monitor) |
| ¦ ¦--<playback> | Specifies a playback test. Currently, not supported.(see playback) |
| ¦ ¦--<testcase> | Specifies a junit testcase.(see testcase) |
| ¦ ¦--<bundle> | Specifies an Open Services Gateway
Initiative (OSGi) bundle should be created.(see bundle) |
| ¦ ¦--<managedbundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed bundle should be created.(see managedbundle) |
| ¦ ¦--<managedfactorybundle> | Specifies an Open Services Gateway
Initiative (OSGi) managed factory bundle should
be created.(see managedfactorybundle) |
Eclipse.org